Results for “how to fix a leaking faucet washer” · retrieved September 20, 2026

Quick answer

To fix a leaking faucet washer, shut off the water supply, disassemble the handle to remove the valve stem, and replace the worn rubber washer with an identical new one.

Answer details

1

Shut off water and relieve pressure

Always shut off the water supply valves under the sink and open the faucet to bleed off residual pressure before starting any disassembly to avoid water damage.

2

Remove the handle carefully

Use a flathead screwdriver to gently pry off the handle cap, then remove the handle screw to lift the handle off. If stuck due to mineral buildup, use penetrating oil rather than force.

3

Match the replacement washer exactly

Take the old washer to the hardware store to ensure you purchase an exact match in diameter and thickness, as incorrect sizes will not seal properly.

4

Lubricate with plumber's grease

Apply a thin layer of plumber's silicone grease to the new washer and stem threads to ensure a smooth, long-lasting seal and prevent the rubber from drying out.

thisoldhouse.com

How to Repair a Leaking Faucet - This Old House

- Adjustable wrench- Faucet handle puller...- Seat redressing tool...1. Start by using a small slotted screwdriver or utility knife to pry off the “hot” and “cold” cover plates from the faucet handles, exposing the attachment screws....2. Use a screwdriver to remove the screw securing each faucet handle. 3. Carefully pull the handles straight up and off the faucet deck. If the handles are stuck, free them using a handle puller. 4. Faucets made wi

June 3, 2014

portland.gov

How to fix a faucet leak | Portland.gov

Leaks not only put stress on the drinking water system, but also send clean water to the wastewater treatment plant. Reduce your impact on the environment and save money and water by repairing some leaks yourself! Follow these easy steps to fix a leaky faucet....- A roll of 1/2″ Teflon tape- A roll of 3/4″ masking tape- Flat head screwdriver- Phillips head screwdriver- Adjustable crescent wrench- Petroleum jelly- Replacement O-rings and/or washer

Publication date not supplied

homedepot.com

6 Steps to Fix a Leaky Faucet

Powered and protected by

July 23, 2025

angi.com

How To Fix A Leaky Faucet [Guide] | Angi

A leaking faucet stems from worn-out washers, deteriorated O-rings, corroded valve seats, or loose screws that prevent your faucet from sealing properly....You can stop the drip by identifying your faucet type, turning off the water supply, and replacing the worn washer or O-ring....Some of the most common culprits of dripping faucets are loose screws, washer problems, and corroded o-rings or valve seats. Once you discover the reason for the leak

November 29, 2021

home.howstuffworks.com

How To Fix a Leaky Faucet | HowStuffWorks - Home and Garden

How To Fix a Leaky Faucet "" A typical compression-type stem faucet is closed by a washer when the handle is turned. Most leaks are caused by faulty washers. HSW...The first thing to do when fixing a faucet drip is to turn off the water supply. You should be able to turn off the supply at a nearby shutoff, but if your house is not equipped with shutoffs for individual fixtures, you'll have to go to the main shutoff and turn off the entire wat

Publication date not supplied

engineerskill.blog

How to Change a Washer in a Leaky Faucet [DIY Repair Guide] - EngineerSkill.blog

To change a washer in a leaky faucet, first shut off the water supply, disassemble the faucet handle to remove the internal stem, and replace the worn rubber washer at the base with an identical new one. This common repair addresses drips in compression-style faucets, which rely on a rubber seal to stop water flow. By mastering this simple fix, you can prevent water waste and avoid the cost of a professional plumber. Image taken from the YouTube

June 9, 2026

thehandyhearth.com

How to Fix a Leaky Faucet (Step by Step, Any Type)

Here’s the whole thing, start to finish. Learning how to fix a leaky faucet is one of those first-home skills that feels like it should need a plumber and almost never does. Ninety percent of the time it’s a worn washer, a cracked O-ring, or a tired cartridge, and all three are a few dollars and a screwdriver away. I’ll show you how to tell which one you’ve got, and exactly what to do about it....You can’t fix the leak until you know your faucet

August 24, 2026

plumbinc.net

How to Fix a Leaking Faucet: Cartridge, Compression, and Ball Valve - Plumb Inc - Plumber

Most faucet drips are caused by a worn cartridge, washer, or O-ring — a $10 part and 30 minutes of work. Identify your faucet type first (cartridge, compression, or ball), shut off supply, swap the worn component, reassemble. The hardest part is usually loosening corroded mounting nuts on older LA homes....1. Identify your faucet type2. Gather tools and shut off water3. Disassemble the handle4. Replace the cartridge or washer5. Reassemble and tes

May 8, 2026

Keep exploring

Related on this site

This page was prepared by Seeked from live retrieval on September 20, 2026 and is not continuously updated. Run a fresh search for the latest, or to inspect each source.